[Free] 2019(Nov) EnsurePass Juniper JN0-102 Dumps with VCE and PDF 331-340

Get Full Version of the Exam

Question No.331

Which statement is correct regarding exception traffic on Junos devices?

  1. The Junos OS does not provide congestion control for exception traffic sent to the RE.

  2. The built-in rate limiter for exception traffic is configurable.

  3. All exception traffic destined for the RE is sent over the out-of-band management link.

  4. The Junos OS has a built-in rate limiter for exception traffic.

Correct Answer: D

Question No.332

You must configure the 2bfc:0000:0000:beef:0217:cbff:0000:5c85 IPv6 address on your device. In this scenario, which three addresses are correct? (Choose three.)

A. 2bfc::beef:217:cbff:0:5c85

B. 2bfc:0:0:beef:0217:cbff:0:5c85

C. 2BFC::BEEF:0217CBFF:0:5C85 D. 2bfc:0:beef:0217:cbff:0:5c85

E. 2BFC::BEEF:217:CBFF::5C85

Correct Answer: ABC

Question No.333

For the interface ge-1/2/3.4, what does quot;gequot; represent?


  2. Gigabit Ethernet

  3. Aggregated Ethernet

  4. GRE

Correct Answer: B

Question No.334

You suspect a duplicate MAC address on a subnet. You want to display the MAC, errors, and statistics of the ge-0/0/0 interface. Which command will accomplish this task?

  1. show arp

  2. show interface ge-0/0/0 extensive

  3. show ethernet-switching table

  4. show interface terse

Correct Answer: B

Question No.335

Click the Exhibit button.


You asked to create a firewall filter to count IPv6 packets that arrive with a no next header value. As shown in the exhibit, you have created and applied the count-no-header firewall filter to the ge-0/0/0 interface. The commit operation fails.

What is causing this problem?

  1. IPv6 interfaces do not support firewall filters.

  2. The filter name must be different than the counter name.

  3. The firewall term does not include inet6 in the from statement.

  4. The firewall family is not correct.

Correct Answer: D

Question No.336

Which command would correctly define a router#39;s host-name?

  1. # set ip host-name lt;namegt;

  2. gt; set ip host-name lt;namegt;

  3. # set system host-name lt;namegt;

  4. gt; set system host-name lt;namegt;

Correct Answer: C


Configure the hostname, using the set system host-name command.


user@host# set system host-name newton-re0


http://www.juniper.net/techpubs/en_US/junos15.1/topics/example/router-namedomain-name-ip- address-system-id-configuring.html

Question No.337

Which two commands is used to validate the syntax of a configuration without applying the configuration?

  1. commit check

  2. commit confirmed

  3. commit synchronize

  4. commit and-quit

Correct Answer: AB

Question No.338

Which statement is correct about the validate option when upgrading JUNOS software?

  1. It will check the MD5 checksum of the install package.

  2. It will check if the device meets the memory requirements for the install package.

  3. It will check the compatibility of the configuration with the install package.

  4. It will check if the device meets the storage requirement for the install package.

    Correct Answer: C


    When you upgrade or downgrade Junos OS, we recommend that you include the validate option with the request system software add command to check that the candidate software is compatible with the current configuration. By default, when you add a package with a different release number, the validation check is done automatically.

    References: https://www.juniper.net/techpubs/en_US/junos12.3/topics/task/operational/junoscandidate- software-compatibility-verifying.html

    Question No.339

    Which two loopback types are supported for serial interfaces on Juniper devices? (Choose two.)

    1. Local

    2. Far End

    3. Remote

    4. Bidirectional

Correct Answer: AC


For serial interfaces Juniper devices support the local and the remote loopback types.

References: http://www.juniper.net/documentation/en_US/junos12.3/topics/usageguidelines/interfaces- interface-diagnostics.html

Question No.340

You are performing the initial configuration of an SRX Series device. What must you set before the device will allow you to commit your configuration?

  1. management interface

  2. system time

  3. hostname

  4. root authentication

Correct Answer: D

Get Full Version of the Exam
JN0-102 Dumps
JN0-102 VCE and PDF