[Free] 2019(Nov) EnsurePass Juniper JN0-102 Dumps with VCE and PDF 341-350

Get Full Version of the Exam

Question No.341

Which CIDR notation is the equivalent of the subnet mask of









Correct Answer: B

Question No.342

Which three SONET network elements are used for troubleshooting? (Choose three.)

  1. line

  2. path

  3. circuit

  4. section

  5. segment

Correct Answer: ABD


Section, line, and path errors occur over different spans of the SONET network and between different pieces of equipment.


http://www.juniper.net/documentation/en_US/junos15.1/topics/topic-map/sonetinterfaces-alarms- and-errors.html

Question No.343

Click the Exhibit button.


Referring to the exhibit, which OSPF feature would connect Area 2 to Area 0?

  1. route summarization

  2. equal-cost multipath

  3. virtual link

  4. database synchronization

Correct Answer: C

Question No.344

Which command prompt indicates that you are in operational mode?

  1. user @ router amp;

  2. user @ router #

  3. user @ router $

  4. user @ router gt;

Correct Answer: D

Question No.345

Which two are correct when configuring an IP address for a Fast Ethernet interface? (Choose two.)

  1. set interfaces fe-0/0/0 address

  2. set interfaces fe-0/0/0.0 family inet address

  3. set interfaces fe-0/0/0.0 address

  4. set interfaces fe-0/0/0 unit 0 family inet address

Correct Answer: BD


D: The following configuration is sufficient to get a Fast Ethernet interface up and running. By default, IPv4 Fast Ethernet interfaces use Ethernet version 2 encapsulation.


user@host# set interfaces fe-5/2/1 unit 0 family inet address local-address

B: You can alos omit the unit specification, here unit 0, and set the ip address through the command:

set interfaces fe-0/0/0.0 family inet address local-address References:

http://www.juniper.net/documentation/en_US/junos12.3/topics/example/interfacesconfiguring-fast- ethernet-interfaces.html

Question No.346

What information does the help topic command provide?

  1. router#39;s version and serial number to help open a case with JTAC

  2. software documentation describing features and configuration tasks within JUNOS

  3. a brief description of commands and their default values

  4. a verification of the current configuration on the router

Correct Answer: B


The help topic command displays usage guidelines for the statement based on information that appears in the Junos OS configuration guides.

Question No.347

Which source of routing information is preferred by default?

  1. static

  2. RIP

  3. direct

  4. BGP

Correct Answer: C

Question No.348

Which parameter must be included when executing operational mode commands from within configuration mode?

  1. run

  2. prompt

  3. insert

  4. do

Correct Answer: A

Question No.349

When you display the routing table by entering the show route command, what does the * indicate?

  1. The route is a direct route.

  2. The route was selected as active.

  3. The route is a default route.

  4. The route was learned using a dynamic routing protocol.

Correct Answer: B


An asterisk (*) indicates that the route is both the active and the last active route. An asterisk before a to line indicates the best subpath to the route.

References: https://www.juniper.net/documentation/en_US/junos14.1/topics/reference/commandsummary/sho w-route-detail.html

Question No.350

After factory-defaults have been loaded, which two syslog files will be present in the configuration?

  1. system and chassis

  2. syslog-messages and NVRAM

  3. messages and interactive-commands

  4. authorization and events

Correct Answer: C

Get Full Version of the Exam
JN0-102 Dumps
JN0-102 VCE and PDF