[Free] EnsurePass Cisco 300-135 Real Exam Dumps Questions 21-30

Get Full Version of the Exam

Question No.21

The following commands are issued on a Cisco Router:

Router(configuration)#access-list 199 permit tcp host host

Router(configuration)#access-list 199 permit tcp host host Router(configuration)#exit

Router#debug ip packet 199

What will the debug output on the console show?

  1. All IP packets passing through the router

  2. Only IP packets with the source address of

  3. All IP packets from to

  4. All IP Packets between and

Correct Answer: D

Question No.22

What level of logging is enabled on a Router where the following logs are seen?

%LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up

  1. alerts

  2. critical

  3. errors

  4. notifications

Correct Answer: D

Question No.23

You have the followings commands on your Cisco Router:

ip ftp username admin ip ftp password backup

You have been asked to switch from FTP to HTTP. Which two commands will you use to replace the existing commands?

  1. ip http username admin

  2. ip http client username admin

  3. ip http password backup

  4. ip http client password backup

  5. ip http server username admin

  6. ip http server password backup

Correct Answer: BD

Question No.24

You have 2 NTP servers in your network – and You want to configure a Cisco router to use as its NTP server before falling back to Which commands will you use to configure the router?

  1. ntp server ntp server

  2. ntp server

    ntp server primary

  3. ntp server

    ntp server prefer

  4. ntp server fallback ntp server

Correct Answer: C

Question No.25

The following command is issued on a Cisco Router: Router(configuration)#logging console warnings Which alerts will be seen on the console?

  1. Warnings only

  2. debugging, informational, notifications, warnings

  3. warnings, errors, critical, alerts, emergencies

  4. notifications, warnings, errors

  5. warnings, errors, critical, alerts

Correct Answer: C

Question No.26

Which two of the following options are categories of Network Maintenance tasks?

  1. Firefighting

  2. Interrupt-driven

  3. Policy-based

  4. Structured

  5. Foundational

Correct Answer: BD

Question No.27

Refer to the Exhibit. Which output is expected in the blank line for the OSPF adjacency process?


  1. DOWN




Correct Answer: B


You can check the output of quot;debug ip ospf adjquot; here:


Question No.28

You are troubleshooting an issue with a GRE tunnel between R1 and R2 and find that routing is OK on all intermediary routers. The tunnel is up on R1, but down on R2. Which two possible issues can prevent the tunnel from coming up? (Choose Two)

  1. The tunnel does not come up unless traffic is sent through it.

  2. The tunnel source interface is down on R2.

  3. No specific route interface is down on R2.

  4. R2 does not know how to reach the tunnel destination.

  5. The tunnel keep alive timer doesn#39;t match on R1 and R2.

Correct Answer: BD


Four Different Tunnel States

There are four possible states in which a GRE tunnel interface can be:

  1. Up/up – This implies that the tunnel is fully functional and passes traffic. It is both adminstratively up and it#39;s protocol is up as well.

  2. Adminstratively down/down – This implies that the interface has been administratively shut down.

  3. Up/down – This implies that, even though the tunnel is administratively up, something causes the line protocol on the interface to be down.

  4. Reset/down – This is usually a transient state when the tunnel is reset by software. This usually happens when the tunnel is misconfigured with a Next Hop Server (NHS) that is it#39;s own IP address.

When a tunnel interface is first created and no other configuration is applied to it, the interface is not shut by default:


Question No.29

Refer to the exhibit. Which two statements are correct? (Choose Two)


  1. The source device has name resolution configured.

  2. The source device is using two routes for the destination, learned from different protocols.

  3. A device on the path is introducing considerable delay.

  4. The source device is loading balancing traffic.

Correct Answer: AD


Router traces domain name (cisco.com) and it gets ICMP answers, so name resolution has happened.

Per hop output shows 2 lines, hence 2 active paths exist.

Question No.30

Refer to exhibit. R1 and R2 are directly connected using interface Ethernet0/0 on both sides. R1 and R2 were not becoming adjacent, so you have just configured R2 interface Ethernet0/0 as network type broadcast. Which two statements are true?

  1. Three OSPF routers are in the network segment connected to

  2. R1 installs a route to as O.

  3. R2 is not an OSPF ABR.

  4. R1 interface Ethernet0/0 is configured as OSPF type point to point.

  5. R1 installs a route to as O IA.

  6. both routers R1 and R2 are neighbors and R2 IS BDR.

Correct Answer: EF


For the Answer 5 quot;R1 installs a route to as O IAquot;:

That because the route belong to another area (area1). -for the Answer 6 quot;both routers R1 and R2 are neighbors, and R2 IS BDRquot;:

Here clearly the question, say that R1 and R2 are not adjacent, but that not mean they are not neighbors, from the output of quot;show ip ospf neighborquot; command we can see clearly that routers R1 and R2 are neighbors, and actually the R2 is BDR.

There different between adjacent and neighbor, neighborsquot; and quot;adjacentquot;. Two terminologies that doesn#39;t mean the same thing, but can often be misused in a discussion. Neighbors in this case means quot;show up as neighbors while using the show ip ospf neighbors commandquot;. While quot;adjacentquot; means they are fully exchanging topology information.

For further information check the links below: https://learningnetwork.cisco.com/message/564573#564573 http://blog.ine.com/2008/01/08/understanding-ospf-network-types/

Get Full Version of the Exam
300-135 Dumps
300-135 VCE and PDF